Fortigate USB disk

-

 insert a 2T USB flash drive to Fortigate-70F:



FortiGate-70F # exe usb-device list
T:  Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=5000 MxCh= 1
B:  Alloc=  0/800 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 3.00 Cls=09(hub  ) Sub=00 Prot=03 MxPS= 9 #Cfgs=  1
P:  Vendor=1d6b ProdID=0003 Rev= 3.0a
S:  Manufacturer=Linux 3.10.15 xhci-hcd
S:  Product=xHCI Host Controller
S:  SerialNumber=f3008000.usb3
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms
T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480  MxCh= 1
B:  Alloc=  0/800 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev= 3.0a
S:  Manufacturer=Linux 3.10.15 xhci-hcd
S:  Product=xHCI Host Controller
S:  SerialNumber=f3008000.usb3
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=048d ProdID=1234 Rev= 2.00
S:  Manufacturer=USB
S:  Product=Disk 3.0
S:  SerialNumber=9207501047790719035
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

FortiGate-70F # get hardware status
Model name: FortiGate-70F
ASIC version: SOC4
CPU: ARMv8
Number of CPUs: 8
RAM: 3717 MB
EMMC: 3742 MB(MLC) /dev/mmcblk0
Hard disk: not available
USB Flash: 0 MB
Network Card chipset: FortiASIC NP6XLITE Adapter (rev.)

FortiGate-70F # exe usb-disk list
unable to mount usb disk
Command fail. Return code -160


FortiGate-70F # get system auto-install
auto-install-config : enable
auto-install-image  : enable
default-config-file : fgt_system.conf
default-image-file  : image.out


FortiGate-70F # execut usb-disk format
This operation will ERASE all data in USB disk!
Do you want to continue? (y/n)y
Format USB disk /dev/sda ...
Create file system on /dev/sda1 ...

FortiGate-70F # execute usb-disk list
FortiGate-70F # get hardware status
Model name: FortiGate-70F
ASIC version: SOC4
CPU: ARMv8
Number of CPUs: 8
RAM: 3717 MB
EMMC: 3742 MB(MLC) /dev/mmcblk0
Hard disk: not available
USB Flash: 1999510 MB
Network Card chipset: FortiASIC NP6XLITE Adapter (rev.)
FortiGate-70F #



After backup to USB disk:


FortiGate-70F # exe usb-disk list
2023-02-17 16:30:55         324305      base.cfg

FortiGate-70F #

Comments

Post a Comment

Popular posts from this blog

Firepower FMC and FTD troubleshooting

-
 1. Display real time log on FMC or FTD: pigtail for example: pigtail | grep 192.168.2.20                      pigtail | grep sftunnel 2. Restart communication channel manage_procs.pl run it from  the sensor only, run it from FMC will reset all sensors' channel. This scripts are nice to be used when the FMC and FTD have communication problems like heartbeats are not received, policy deployment is failing or events are not received > expert ************************************************************** NOTICE - Shell access will be deprecated in future releases          and will be replaced with a separate expert mode CLI. ************************************************************** admin@FTD:~$ sudo su Password: root@FTD:/home/admin# manage_procs.pl ****************  Configuration Utility  **************  1   Reconfigure Correlator  2   Reconfigure and flush Correlator  3    Restart Comm. channel  4   Update routes  5   Reset all routes  6   Validate Network  0   Exit *****
Read more

ASA IKEv1 VPN troubleshooting Steps and Tips

-
  1. Phase I proposal mismatch  Run show crypto isakmp sa  Initiator: MM_WAIT_MSG2 Responder: No info  Most likely this is phase1 proposal mismatch, verify IKEv1 policy, other symptoms:   Initiator log: Information Exchange processing failed All configured IKE versions failed to establish the tunnel Initiator debug: Received an un-encrypted NO_PROPOSAL_CHOSEN notify message, dropping Responder log: Error processing payload: Payload ID Responder debug:  All SA proposals found unacceptable 2. IKE version mismatch:  Run  show crypto isakmp sa  no info at both initiator and responder Initiator log: Removing peer from correlator table failed, no match! Reason: User Requested  All configured IKE versions failed to establish the tunnel Initiator debug: Oakley begin quick mode PHASE 1 COMPLETED IKE Initiator sending 1st QM pkt Removing peer from correlator table failed, no match! Session is being torn down. Reason: User Requested Responder log: Tunnel Rejected: Conflicting protocols specified
Read more

Firepower 2100/1100 FTD/ASA initial setup, reimage, upgrade.

-
  Chassis FXOS and FTD share same management IP (default 192.168.45.45) Chassis FXOS (192.168.45.45) and ASA ()use different management IP although on same physical interface. SSH to FXOS/FTD are on FTD CLI prompt, go to FXOS using the  connect fxos  command Console to Chassis is on FXOS CLI prompt, go to FTD using the  connect ftd  command The Firepower 1100 does not support the FXOS Firepower Chassis Manager; only a limited CLI is supported for troubleshooting purposes. The Firepower 2100 runs an underlying operating system called the Firepower eXtensible Operating System (FXOS).  If you run ASA on Firepower 2100, ASA can be in the following modes: Appliance mode (the default after ASA 9.13)—Appliance mode lets you configure all settings in the ASA. Only advanced troubleshooting commands are available from the FXOS CLI. See the  FXOS troubleshooting guide  for more information. Firepower Chassis Manager is not supported . ciscoasa# connect fxos [admin] Connecting to fxos. Connected
Read more