PPP Multilink

-
R1(config)#int s1/0
R1(config-if)#encapsulation ppp
R1(config-if)#ppp multilink group 1
R1(config-if)#no shut

R1(config-if)#do sh run int s1/0
Building configuration...
Current configuration : 108 bytes!

interface Serial1/0
no ip address
encapsulation ppp
serial restart-delay 0
ppp multilink group 1
end

R1(config-if)#int s1/1
R1(config-if)#encapsulation ppp
R1(config-if)#ppp multilink group 1
R1(config-if)#no shut

R1(config-if)#do sh run int s1/1
Building configuration...
Current configuration : 118 bytes!

interface Serial1/1
no ip address
encapsulation ppp
serial restart-delay 0
ppp multilink group 1
end

R1(config-if)#int multilink 1

After created the multilink interface, some commands are automatically added in serial interfaces and multilink interface

R1(config-if)#do sh run int s1/0
Building configuration...
Current configuration : 123 bytes!

interface Serial1/0
no ip address
encapsulation ppp
serial restart-delay 0
ppp multilink
ppp multilink group 1
end

R1(config-if)#do sh run int s1/1
Building configuration...
Current configuration : 123 bytes!

interface Serial1/1
no ip address
encapsulation ppp
serial restart-delay 0
ppp multilink
ppp multilink group 1
end

R1(config-if)#do sh run int mul1
Building configuration...
Current configuration : 81 bytes!

interface Multilink1
no ip address
ppp multilink
ppp multilink group 1
end

Comments

Post a Comment

Popular posts from this blog

Firepower FMC and FTD troubleshooting

-
 1. Display real time log on FMC or FTD: pigtail for example: pigtail | grep 192.168.2.20                      pigtail | grep sftunnel 2. Restart communication channel manage_procs.pl run it from  the sensor only, run it from FMC will reset all sensors' channel. This scripts are nice to be used when the FMC and FTD have communication problems like heartbeats are not received, policy deployment is failing or events are not received > expert ************************************************************** NOTICE - Shell access will be deprecated in future releases          and will be replaced with a separate expert mode CLI. ************************************************************** admin@FTD:~$ sudo su Password: root@FTD:/home/admin# manage_procs.pl ****************  Configuration Utility  **************  1   Reconfigure Correlator  2   Reconfigure and flush Correlator  3    Restart Comm. channel  4   Update routes  5   Reset all routes  6   Validate Network  0   Exit *****
Read more

ASA IKEv1 VPN troubleshooting Steps and Tips

-
  1. Phase I proposal mismatch  Run show crypto isakmp sa  Initiator: MM_WAIT_MSG2 Responder: No info  Most likely this is phase1 proposal mismatch, verify IKEv1 policy, other symptoms:   Initiator log: Information Exchange processing failed All configured IKE versions failed to establish the tunnel Initiator debug: Received an un-encrypted NO_PROPOSAL_CHOSEN notify message, dropping Responder log: Error processing payload: Payload ID Responder debug:  All SA proposals found unacceptable 2. IKE version mismatch:  Run  show crypto isakmp sa  no info at both initiator and responder Initiator log: Removing peer from correlator table failed, no match! Reason: User Requested  All configured IKE versions failed to establish the tunnel Initiator debug: Oakley begin quick mode PHASE 1 COMPLETED IKE Initiator sending 1st QM pkt Removing peer from correlator table failed, no match! Session is being torn down. Reason: User Requested Responder log: Tunnel Rejected: Conflicting protocols specified
Read more

Firepower 2100/1100 FTD/ASA initial setup, reimage, upgrade.

-
  Chassis FXOS and FTD share same management IP (default 192.168.45.45) Chassis FXOS (192.168.45.45) and ASA ()use different management IP although on same physical interface. SSH to FXOS/FTD are on FTD CLI prompt, go to FXOS using the  connect fxos  command Console to Chassis is on FXOS CLI prompt, go to FTD using the  connect ftd  command The Firepower 1100 does not support the FXOS Firepower Chassis Manager; only a limited CLI is supported for troubleshooting purposes. The Firepower 2100 runs an underlying operating system called the Firepower eXtensible Operating System (FXOS).  If you run ASA on Firepower 2100, ASA can be in the following modes: Appliance mode (the default after ASA 9.13)—Appliance mode lets you configure all settings in the ASA. Only advanced troubleshooting commands are available from the FXOS CLI. See the  FXOS troubleshooting guide  for more information. Firepower Chassis Manager is not supported . ciscoasa# connect fxos [admin] Connecting to fxos. Connected
Read more